冷再生工作裝置主要由大臂、轉子、轉子罩等組成。拌刀為子彈頭式，罩殼為全浮動拖式。冷再生機租賃廠家提醒您，工作裝置是穩定土再生機的主要工作機構，直接體現該機功能。作業過程中，作業的平整度、壓實度、拌料的含水量等因素直接影響到再生效果及生產效率。

The cold regeneration working device is mainly composed of boom, rotor, rotor cover, etc. The mixing knife is bullet head type, and the cover is full floating towed type. The leasing manufacturer of the cold regenerator reminds you that the working device is the main working mechanism for stabilizing the soil and reinvigorating it, which directly reflects the function of the machine. During the operation, the flatness, compactness and moisture content of the mixture directly affect the regeneration effect and production efficiency.

舉升臂

Boom

左右舉升臂和兩根橫梁組成，與主機架的后部支座鉸接，它可繞這個鉸接軸轉動，由舉升臂升降油缸來驅動。其主要作用是帶動整個工作裝置隨車運動和升降運動。舉升臂外側防護板可以取下，里面有工作馬達和膠管。

The left and right boom is composed of two beams, which are hinged with the rear support of the main frame. It can rotate around this hinge axis and is driven by the boom lifting cylinder. Its main function is to drive the whole working device to move with the vehicle and move up and down. The outer guard plate of the boom can be removed, and there are working motors and rubber hoses inside.

工作轉子

Working rotor

轉子是由刀庫、刀頭、刀座等組成。轉子通過內外齒圈、壓盤、和舉升臂連接在一起。內齒圈與舉升臂固定在一起，外齒圈與支座定在一起，的旋轉部件與轉子固定在一起，內外齒圈嚙合用壓盤從轉子兩端壓合。

The rotor is composed of tool magazine, tool head, tool holder, etc. The rotor is connected with the lifting arm through the inner and outer gear rings, pressure plates and. The inner gear ring is fixed with the lifting arm, the outer gear ring is fixed with the support, the rotating parts of the are fixed with the rotor, and the inner and outer gear ring mesh is pressed from both ends of the rotor with a pressure plate.

動力來自工作馬達，其作用是減小轉速，增加扭矩，并把動力傳遞給轉子。轉子的作用是銑削、破碎、拌合物料，并把物料拋到后面。轉子的銑刨深度可從舉升臂油缸上的標尺讀出來。

The power comes from the working motor, whose function is to reduce the speed, increase the torque and transfer the power to the rotor. The role of the rotor is to mill, break, mix materials and throw them behind. The milling depth of the rotor can be read from the scale on the boom cylinder.

轉子罩殼

Rotor housing

它由頂罩板和兩側罩板焊接而成的半圓形罩殼。其后部有后尾門，開度由油缸控制，作用是刮平拌合好的物料，前部有前尾門，開度由兩拉桿調整，作用是控制物料粒度，開度越小粒度越小，但作業阻力也越大。整個轉子罩空套在內齒圈上，進行銑拌作業時，罩殼浮在地面上，與地面形成一個封閉的空間。

It is a semi-circular shell welded by the top cover plate and the cover plates on both sides. There is a rear tailgate at the rear, whose opening is controlled by the oil cylinder, which is used to scrape and level the mixed materials. There is a front tailgate at the front, whose opening is adjusted by two pull rods, which is used to control the particle size of materials. The smaller the opening, the smaller the particle size, but the greater the operating resistance. The whole rotor casing is sleeved on the inner gear ring. When milling and mixing, the casing floats on the ground, forming a closed space with the ground.

這樣銑拌刀具切削混凝土，并以一定的速度拋進來，撞擊轉子罩的內面，使穩定土進一步破碎，同時把各種成分混合均勻，以一定的速度把物料從轉子上面的空間拋到后面，后物料從后尾門流出，后尾門將其刮平。

In this way, the milling cutter cuts the concrete and throws it in at a certain speed, hitting the inner surface of the rotor cover, further crushing the stabilized soil, and mixing the various components evenly. At a certain speed, the material is thrown from the space above the rotor to the rear, and the rear material flows out from the rear tailgate, and the rear tailgate scrapes it flat.

冷再生機工作裝置的功能是把舊路面連同基層銑刨下來，在轉子罩和轉子形成的拌合室內，把銑刨下來的物料和添加得物料破碎并拌合均勻，再以均勻得速度鋪在銑刨過得路面上，形成新的穩定土層。您對此有怎樣的疑惑或者需求，隨時來我們網站http://www.cpssc145.com進行咨詢！

The function of the working device of the cold regenerator is to mill the old road surface together with the base layer, break and mix the milled and added materials in the mixing room formed by the rotor cover and rotor, and then pave the milled road surface at a uniform speed to form a new stable soil layer. If you have any doubts or needs about this, please come to our website at any time http://www.cpssc145.com Consult!