一、清洗外表

1、 Cleaning the exterior

冷再生機在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。

During the construction process of the cold regeneration machine, a large amount of dust will fall onto the surface of the regeneration machine, including pollutants such as oil stains during construction, which have a small impact on the appearance and, more seriously, become an inducing factor for corrosion.

冷再生機租賃廠家提醒，清洗工程機械的柴油機、底盤、工作裝置的外表,除垢、除油保持再生機的外觀整潔。清洗時嚴禁用高壓、高溫的水槍來沖洗防水要求較高的部位（特別是電器部分），以免造成電器部分的損壞。

Cold regeneration machine rental manufacturers remind us to clean the exterior of the diesel engine, chassis, and working devices of construction machinery, remove dirt and oil, and keep the appearance of the regeneration machine clean. It is strictly prohibited to use high-pressure and high-temperature water guns to wash parts with high waterproof requirements (especially electrical parts) during cleaning, in order to avoid damage to the electrical parts.

二、保養轉子及其罩殼和滑靴

2、 Maintain the rotor and its casing and shoes

1.檢查轉子是否有水泥結垢等，及時清理灰塵，對需要割除、焊接的刀具及時更換；

1. Check if there is cement scaling on the rotor, clean the dust in a timely manner, and replace the cutting tools that need to be cut or welded in a timely manner;

2.清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5-10公分，防止雨雪的浸蝕；

2. Clean the dust on the rotor casing and pad the rotor casing 5-10 cm above the ground at the end of construction to prevent erosion by rain and snow;

3.檢查滑靴，對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。

3. Check the sliding shoes, repair welding the worn parts of the sliding shoes, and apply butter to the threads for rust prevention.

三、減速機齒輪油的更換方式

3、 Replacement method of reducer gear oil

減速機油位及減速機油的檢查：先切斷電源，等待減速機冷卻后打開放油螺塞，檢查油是否充滿，避免漏油，取油樣，檢查油色澤及粘度指數，如果油明顯渾濁，建議盡快更換。新減速機使用后（500-1000）小時更換新油（將內部污油沖干凈），其后每使用1500小時需要更換油一次，但是在使用過程中，仍需要檢查油的質量，若油有老化、變質情況要隨時更換。

Inspection of gearbox oil level and reducer oil: First cut off the power supply, wait for the gearbox to cool down, open the oil drain plug, check whether the oil is full to avoid oil leakage, take an oil sample, check the oil color and viscosity index. If the oil is significantly turbid, it is recommended to replace it as soon as possible. After the new gearbox is used (500-1000 hours), replace it with new oil (flush out the internal dirty oil). Afterwards, the oil needs to be replaced every 1500 hours of use. However, during use, the quality of the oil still needs to be checked. If the oil has aged or deteriorated, it should be replaced at any time.

冷再生機機械的保養注意事項就從這三個方面來講解一番，希望能夠給您好的幫助，更多事項就來我們的網站http://www.cpssc145.com咨詢吧！

The maintenance precautions for the cold regeneration machine machinery will be explained from these three aspects. We hope to provide you with good help. For more details, please visit our website http://www.cpssc145.com Consult!